RECOMMENDED FOR
Waterproofing and protection of:
- Gypsum and cement boards
- polyurethane insulation foams
- asphalt membranes
- EPDM membranes
- bathrooms (under tiles)
- verandas and balconies (under tiles)
- flower pots and roof-top gardens
- light roofing made of metal or fibrous cement
- non-potable water tanks
- basements
- foundations
- bridge platforms
- cut-and-cover tunnels
- Irrigation channels
LIMITATIONS: Not recommended for unsound substrates.
APPLICATION PREREQUISITES
Can be successfully applied on:
Concrete, fibrous cement, mosaic, cement roof tiles, old (but well adhered) acrylic and asphalt coats, wood, corroded metal, and galvanized steel. For information about other substrates, please contact our tech department.
Concrete substrate conditions (standard):
- Hardness: R28 = 15Mpa
- Humidity: W < 10%
- Temperature: 5-35 oC
- Relative humidity: < 85%
Primer selection for special conditions and substrates: Please refer to the Primer Selection Table.
APPLICATION PROCEDURE
Clean the surface using a high pressure washer, if possible. Remove oil, grease and wax contaminants. Cement laitance, loose particles, mould release agents, cured membranes, etc. must be removed.
Priming:
Choose primer from the Primer Selection Table and follow the application instructions given on its prospectus.
Mixing:
Mix equal volumes of the two components manually or with a low speed (300 rpm) mixer. Apply mixed quantities immediately. Pot life (of mix): 30-45 minutes at 20 oC. For application by airless spraying, the mix may have to be thinned with a small quantity of SOLVENT-01, especially for low-power applicators.
Crack bridging:
Apply HYPERDESMO-PB-2K (or HYPERDESMO-PB-1K) locally over any cracks larger than 1 mm before the main coat.
Application:
Apply the material with brush, roller or spatula.
CONSUMPTION
Minimum consumption: 1.0-1.5 lt/m2.
CLEANING
Clean tools and equipment first with paper towels and then using SOLVENT-01. Rollers will not be re-usable.
PACKAGING
2×5 lit, 2×20 lit and 2×200 lit.
SHELF LIFE
Can be kept for 12 months minimum in the original unopened pails in dry places and at temperatures of 5-25 oC. Cap tins air tightly in order to store unused quantities.
PRECAUTIONS
Contains a small quantity of volatile flammable solvents. Apply in well-ventilated, no smoking areas, away from naked flames. In closed spaces use ventilators and carbon active masks. Keep in mind that solvents are heavier than air so they creep on the floor. The MSDS (Material Safety Data Sheet) is available on request
TECHNICAL SPECIFICATIONS
In liquid form (before application): ~90% dry matter in Xylene.
PROPERTY |
UNITS |
METHOD |
SPECIFICATION |
Viscosity (Brookfield) Comp. A: Resin
Comp. B: Asphaltic mix |
cP |
ASTM D2196-86, @ 25 oC |
1300
4300 |
Viscosity (Brookfield) of the mixture |
cP |
ASTM D2196-86, @ 25 oC |
3000 |
Specific weight of the mixture |
gr/cm3 |
ASTM D1475 / DIN 53217 / ISO 2811,
@ 20 oC |
0.97 |
Flash point |
oC |
ASTM D93, closed cup |
> 40 |
Tack-free time, @ 77 oF (25
oC) & 55% RH |
hours |
– |
1-2 |
Recoat time |
hours |
– |
6-24 |
The cured membrane:
PROPERTY |
UNITS |
METHOD |
SPECIFICATION |
Service temperature |
oC |
– |
-40 to 80 |
Max. temperature short time (shock) |
oC |
– |
150 |
Hardness |
Shore A |
ASTM D2240 / DIN 53505 / ISO R868 |
35 |
Tensile strength at break @ 23 oC |
Kg/cm2 (N/mm2) |
ASTM D412 / EN-ISO-527-3 |
> 20
> (2) |
Percent elongation @ 23 oC |
% |
ASTM D412 / EN-ISO-527-3 |
> 1000 |
Tensile set (after 300% elongation) |
% |
ASTM D412 |
< 1% |
Thermal resistance (200 days @ 80 oC) |
– |
EOTA TR011 |
passed |
QUV Accelerated Weathering Test (4hr UV, @ 60 oC (UVB- Lamps) & 4hr COND @ 50
oC) |
– |
ASTM G53 |
passed (1000 hours) |
Chemical resistance (Sodium Hypochlorite NaOCI 5% 10 days) |
– |
– |
unaffected |
Hydrolysis resistance (Potassium Hydroxide 8% 10 days @ 50 °C) |
– |
– |
unaffected |
H2O absorption (10 days) |
– |
– |
< 0.9% |
Reviews
There are no reviews yet.